Part Number: 616.604.102.02
High torque starter (1.9 horsepower) for all 356 models. Brand new (not rebuilt). It works great in hot or cold climates or with engines that have very high compression ratio. 12v system with matched drive gear for a 6v ring gear.

Part Number: SMC.101.001.02
Deep oil sump beautifully machined from aluminum for all 356 and 912 models. Helps to keep oil flowing to the bearings during hard cornering. Magnetic drain plug, seal and all necessary hardware included.

Part Number: SMC.043.803
Rebuild kit for a Bosch cis K Jetronic adjustable fuel injection metering distributor.

Part Number: 999.613.017.40
Black plastic insulator tube for all 356 (1950-1965), 911/912 (1965-1973), 911/930 (1974-1989) and 914 (1970-1976) models.

Part Number: NLA.604.006.06
Currently unavailable

Part Number: NLA.604.004.06
Currently unavailable

Part Number: 901.102.148.00
Lock ring for distributor drive gear. 2.4mm. Fits all 356's (1950-1965), 911 (1965-1969), 912 (1965-1969), 912E (1965-1969) models.

Part Number: 546.06.203
Currently Unavailable

Part Number: SMC.602.101.50
Shim and hardware kit for cast iron distributors only.

Part Number: NLA.602.936.00
Cast iron insulator kit.

Part Number: 356.09.612
Black coil wire from ignition coil to distributor on 356 Pre-A, 356A and 356B models.

Part Number: 616.602.201.06
Complete distributor.

Part Number: SMC.602.201.08
Affordable replacement for the no longer available and expensive Bosch distributor.

Part Number: 616.602.201.FX
Complete distributor with contact breaker point for 1600 and 1600s engines.

Part Number: 644.602.650.04
Tune up part for cast iron or aluminum distributors on all 356's and 912 models.

Part Number: 644.602.301.02
Tune up parts for cast iron or aluminum distributors for all 356 and 912 models. Two required.

Part Number: 113.905.207.C
Bosch part # 1 235 522 056 - 03010. It fits all 356 (1950-1965) models with .009 Distributor, 912 (1965-1969) and 924 (1977-1982) models.

Part Number: 616.602.215.02
Cap for 031 distributor. BERU # VK105-0 330 920 005 and BOSCH part # 1 235 522 050-03005. It fits 356 and 912 models with 031 distributor.

Part Number: 616.602.215.00
Cap for cast iron distributor. BOSCH part # 1 235 522 107 - 03019. It fits all 356 with cast iron distributor and 912(1965-1969) models.

Part Number: 616.602.215.03
Cap for die cast aluminum distributor. BOSCH part # 1 235 522 056 - 03010. It fits 356 with die cast aluminum distributor and 912 (1965-1969).

Part Number: NLA.602.954.00
Clip set for cast iron distributor.

Part Number: 616.602.907.02
Condenser for all 356 (1950-1965) and 912 with "cast iron" distributors and all 911 (1965-1968) models.

Part Number: 901.602.961.01
Condenser for models with die cast aluminum distributors on all 356's (1950-1965) and early 912 (1965-1969) models.

Part Number: 644.602.501.20
Tune up part for 356's and 912 models with cast iron or aluminum distributors.

Part Number: NLA.602.401.10
Tune up part for cast iron or aluminum distributors on 356's (1950-1965) and 912 (1265-1969) models.

Part Number: 539.09.103
Distributor drive spring for 356 (1950-1955), 356A (1955-1959), 356B (1960-1963), 356C (1964-1965) and 912 models (1965-1969).

Part Number: 539.09.313
Tune up part for cast iron or aluminum distributors.

Part Number: NLA.109.953.00
Distributor plug wire set for all 356 and 912 models. Plug connectors NOT included.

Part Number: 644.602.490.00
Tune up part for cast iron or aluminum distributor on all 356's (1950-1965) and 912 (1965-1969) models.

Part Number: 616.602.221.05
Distributor rotor for die cast aluminum distributors on all 356's and early 912 models.

Part Number: 616.602.221.00
Distributor rotor for all 356's and 912 models with cast iron distributors.

Part Number: 999.701.101.50
Tune up part for cast iron or aluminum distributors.

Part Number: NLA.602.102.01
Tune up part for cast iron or aluminum distributors.

Part Number: SMC.107.356.02
Engine tune up for 356 models (1950)-1965) with a die cast aluminum distributor. This kit includes (1) alternator v-belt, (1) oil filter, (1) distributor cap, (1) distributor rotor, (1) distributor condenser, (1) ignition point set, (2) oil sump gaskets and (4) spark plugs.

Part Number: SMC.107.356.01
Engine tune up for 356 models (1950-1965) with a cast iron distributor. This kit includes (1) alternator v-belt, (1) oil filter, (1) distributor cap, (1) distributor rotor, (1) distributor condenser, (1) ignition point set, (2) oil sump gaskets and (4) spark plugs.

Part Number: 616.106.181.00
CURRENTLY UNAVAILABLE

Part Number: 111.903.221.A
Bearing for generator commutator end. Fits all 356 and 912 models (1950-1969).

Part Number: 616.603.904.02
Two brush set for all models with a 6 Volt generators.

Part Number: 616.109.381.00
Generator pole boot for 356B and 356C models.

Part Number: SMC.09.303
Generator pulley nut made from 303 series stainless steel. Fits all 356 (1950-1965) and 912 (1965-1969) models.

Part Number: 539.01.125
Generator stand gasket for all 356 and 912 models.

Part Number: 539.01.145
Generator stand for 356 (1950-1955), 356A (1955-1959), 356B (1960-1963), and 356C (1964-1965) models.

Part Number: 616.603.102.01
Complete rebuilt and tested 12 Volt generator for 356 models with updated (12 Volt) electrical system or 912 models. 60 day warranty and core deposit will be refunded upon receipt of your used generator. Unit has to be in restorable condition and you have up to 120 days send it in for your core deposit refund. Washers & nuts on both ends are not included.

Part Number: 616.603.101.01
Complete rebuilt and tested 6 Volt, 200 watt, 50 amp generator for all 356 models. 60 day warranty and core deposit will be refunded upon receipt of your used generator. Unit has to be in restorable condition and you have up to 120 days send it in for your core deposit refund. Washers & nuts on both ends are not included.

Part Number: N.010.500.3
Hexagon head screw for engine mount. Fits all 356 (1950-1966), 914 (1970-1976) and 928 (1983-1995) models. Measures 10mm x 115mm.

Part Number: 900.074.037.02
Hex-head Screw for 356 Pre-A (1950-1955), 356A (1955-1959), 356B (1960-1963) and 356C (1964-1965) models. Measures 8mm x 35mm.

Part Number: 900.076.013.02
Hexagon Nut, 8 mm, for 356 Pre-A (1950-1955), 356A (1955-1959), 356B (1960-1963) and 356C (1964-1965) models.

Part Number: SMC.602.201.10
This high performance distributor is an excellent improvement from the stock 009 distributor for your 356 or 912 model. It will improve the idle characteristics, have an easier start and provide a low-end throttle response. This is an affordable replacement of your original.

Part Number: NLA.602.108.55
Ignition coil bracket.

Part Number: SMC.602.108
Perfect reproduction of the original Bosch coil bracket. It fits 356A, 356B, 356C, 911(1965-1968), 912(1965-1969) and 914(1970-1976) models.

Part Number: 616.602.109.00
Ignition coil for all 356 (12V), 912(1965-1969) and 914-4 models.

Part Number: 616.602.108.00
Bosch 6V ignition coil with bracket. For authenticity paint it black as the originals.

Part Number: 644.602.108.00
Professionally painted black and the correct 6 volt decal was applied. Bracket (NLA.602.108.55) is not included.

Part Number: 616.602.109.01
It fits: 356 all (12V system), 912 (66-69), 914 (70-71), 914/4 (72-76).

Part Number: 616.602.226.02
One piece point set for 356's and 912 with die cast aluminum distributors, 911 with Bosch distributor (1969-1971) and all 914-6 (1970-1972) models.

Part Number: 616.602.226.01
Two piece ignition point set for all 356's/912 with cast iron distributor and 911(65-68) models.

Part Number: 644.109.952.00
Currently unavailable

Part Number: 616.609.052.10
Beru ignition wire set for all 356's and 912 models. Connectors are now black.

Part Number: 09.267
Currently unavailable

Part Number: SMC.09.315
Silver finish inner half pulley for generator on all 356's and some early 912 models.

Part Number: 528.08.033
Intake manifold set for the early 356 A "S"engines with the 40 PJCB carburetor. New sand cast manifolds batch for 10 sets CNC machines. Made in Holland.

Part Number: N.012.230.1
Lock washer for all 356's (1950-1965) and 911 (1970-1977) models.

Part Number: 546.09.301
Generator and oil filter assembly (canister) mounting strap for 356 (1950-1955), 356A (1955-1959), 356B (1960-1963), 356C (1964-1965) and 912 (1965-1969) with a 285mm generator.

Part Number: SMC.613.571.01
OE type oil pressure switch with screw connection.

Part Number: 901.613.571.01
OE Supplier oil pressure switch for 356's, 911 and 912 models.

Part Number: SMC.09.316
Silver finish outer half pulley for generator on all 356's and some early 912 models. No notches.

Part Number: 911E9021
CURRENTLY UNAVAILABLE

Part Number: 911E905
Perma tune ignition system for 12 volt 356 and all early pre-electronic 911 cars with carburetors.

Part Number: 40011.40511
This 40,000 volt ignition coil benefits virtually any distributor type inductive system.

Part Number: SMC.616.609.80
Pertronix ignition system for all 356's and 912 models. Available in 6V or 12V for cast iron or aluminum distributors.

Part Number: 692.609.301.00
Extra long (BEL 4/1) spark plug connector for all 356's, 912 and 911 models.

Part Number: 616.609.302.00
No longer available

Part Number: 0.300.111.0016
No longer available

Part Number: 999.659.006.50
Protection cap.

Part Number: 547.09.304
Generator stand gasket for all 356 (1950-1965) and 912 (1965-1969) models.

Part Number: 539.09.314
Spacers for pulley on all 356's and 912 models.

Part Number: N.012.709.1
Woodruff key for pulley on all 356's and 912 models.

Part Number: N.012.705.1
Woodruff key for pulley on all 356's and 912 models.

Part Number: NLA.604.611.01
6 volt starter switch relay kit for 4" starter solenoid. Fits all 356 (1950-1965) and 912 (1965-1965) models.

Part Number: 539.09.201
Spark plug connector boot for all 356 (1950-1965), 911 (1965-1989), 912 (1965-1969), 914 (1970-1976), 930 (1976-1989), 912E (1976) and 911 Turbo (1990-1992) models. Please note that all 356's, 912, 912E and 914-4 models require four. All other models require six.

Part Number: 111.905.449.A
Spark plug connector boot for all 356 (1950-1965), 911 (1965-1989), 912 (1965-1969), 914 (1970-1976), 930 (1976-1989), 912E (1976) and 911 Turbo (1990-1992) models. Please note that all 356's, 912, 912E and 914-4 models require four. All other models require six.

Part Number: 122.905.449A
Spark plug connector boot for 356, 911, 912 and 914 models.

Part Number: 616.609.303.00
Spark plug connector for all 356 models.

Part Number: PCG.609.302.00
Spark plug connector for all 356 and 912 (1950-1969) models.